Petrol Transfer 380v Rotary Gear Oil Pump With Safety Valve

Petrol Transfer 380v Rotary Gear Oil Pump With Safety valve

The usage and maintenance

1. Start up preparation:
(1) Take off the sundry from the machine before starting and clean up.

(2) Bearing in vivo perfusion clean hot oil as lubricant , open A, B two holes, by injection from A hole, until B hole has the oil spill, rotate coupling with the hand, there would be no gas from two holes, and restore the two holes to tighten bolts.

(3) Check each part of the pump, motor, pipes and Other junction, should not have loose phenomenon.

(4) Turn the coupling with the hand can light turning, and observe the pump with and without friction, shall be immediately ruled out.

(5) Before driving to pump transmission medium, in the process of filling, slowly turns the coupling with the hand, should avoid up into the air.

(6) Transferring hot oil, while driving to uniform preheating. Preheating is to use the heating medium is to be delivered through the pump body.

Preheat standard: the oil temperature is not higher than 40 ℃, temperature < - 50 ℃ / hour, preheating, loosen bolts should be solid pump 0.3 0.5 mother, after the preheating to tighten it.

(7) Preheating process, should observe the running situation, once found running unhealthy phenomenon, should immediately stop the pump to check.

The KCB crude oil gear pump is equipped with a protection valve as an overload protection. The full return pressure of the protection valve is 1.5 times the rated pressure of the pump. It can also be adjusted according to actual needs within the allowable discharge pressure range. However, please note that this protection valve can not be used for long-term work of the pressure reducing valve. It can be installed separately on the pipeline when needed. Seen from the overhanging end of the spindle to the pump, it rotates clockwise. Flow rate: 1.1m3/h-600m3/h Pressure: 0.28MPa--2.5MP. KCB gear pump is mainly used for oil flow and oil discharge in oil fields, oil depots, ports, docks, ships, etc.

Performance specification

Molde	Capacity(L/MIN)	Pressure(Mpa)	Diameter(mm)	Motor power(KW)
KCB18.3	18.3	1.45	20	1.5
KCB33.3	33.3	1.45	20	2.2
KCB55	55	0.33	25	1.5
KCB83.3	83.3	0.33	40	2.2
KCB135	135	0.33	50	2.2
KCB200	200	0.33	50	4
KCB300	300	0.36	70	5.5
KCB483.3	483.3	0.36	70	7.5
KCB633	633	0.28	100	11
KCB960	960	0.28	100	18.5
KCB1200	1200	0.6	150	37
KCB1600	1600	0.6	150	45
KCB1800	1800	0.6	200	55
KCB2500	2500	0.6	200	75
KCB2850	2850	0.6	250	90
KCB3800	3800	0.6	250	110
KCB5400	5400	0.6	250	160
KCB7600	7600	0.6	350	160
KCB9600	9600	0.6	350	185

Pump's picture

KCB18.3-KCB83.3 model crude oil pump:

KCB135-KCB960 model crude oil pump:

KCB200-KCB9600 model crude oil pump:

Botou Honghai Pump Co., LTD. Is a professional manufacturer specializing in developing and manufacturing various high viscosity pump , heat insulation pump , screw pump , asphalt pump , gear pump , stainless steel pump , high temperature pump , rotor pump , hose pump , and centrifugal pump .
Products are widely used in the national petroleum, chemical, shipping, electricity and other fields.
Our company has a perfect production system and quality assurance system, won the trust of domestic and foreign customers.

Contatc US

Contact us if you need more details on Gear Oil Pump With Safety Valve. We are ready to answer your questions on packaging, logistics, certification or any other aspects about 380v Rotary Gear Oil Pump、Petrol Transfer Gear Pump. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Gear Pump > Gear Oil Pump